sop for cip of mixing vessel mixing mobile vessel and holding vessel
To lay down the procedure for Cleaning of Mixing Vessel/Holding Vessel, Cartridge Housing and Filter Housings and Pipe lines using CIP.
This SOP is applicable to Cleaning of Mixing Vessel/Holding Vessel, Cartridge Housing & Filter Housings and Pipe Lines using CIP of Production Area
Officer/Executive – Production
Head – Production
5.1.1 Ensure the CIP in working condition.
5.1.2 Ensure all the utility supply for CIP operation.
5.1.3 Ensure the mixing tank is empty.
5.2 The Cleaning of Mixing Vessel, Mobile Mixing Vessel, Holding Vessel, Filling Vessel, Filter Housing and Filtration Pipe lines with Purified water followed by rinsed with WFI. The Procedure to be adopted after and before the production processing.
5.3 CIP OF MANUFACTURING & FILTRATION LINE:
5.3.1 MIXING VESSEL, HOLDING VESSEL, FILTRATION LINE, FILTER CARTRIDGES AND BUFFER VESSEL:
22.214.171.124 Connect the CIP outlet supply to inlet of mixing vessel.
126.96.36.199 Connect the filtration line inlet to the mixing vessel outlet and followed by connect filter cartridge.
188.8.131.52 Now connect the filter cartridge outlet to CIP inlet.
184.108.40.206 Clean the outside body of mixing vessel, holding vessel, filtration line, filter cartridge housing and Buffer vessel with Hot WFI using lint free sponge (mopping pad).
220.127.116.11 Clean the mixing vessel vent filter separately with hot WFI and refit it.
18.104.22.168 Clean the sampling valve of mixing vessel.
22.214.171.124 Close the manhole of the mixing vessel with air tight.
126.96.36.199 Now set the IPC of CIP as per following parameter and batch details:
188.8.131.52 1st press of IPC as show Display.
184.108.40.206 2nd Step click .User name & password entry
220.127.116.11 3rd Step Login successes fully for next processing
18.104.22.168 4th Step Welcome MV & MMV tank select for next processing
22.214.171.124 5th Step HV with BV tank select for next processing
126.96.36.199 6th Step go to mode selection for processing.
188.8.131.52 7th Step semi auto mode selection for MV, MMV, HV tank and press the start CIP Pre wash. Cycle complete than after press CIP Intermediate wash mode & final wash mode.
184.108.40.206 8th step Comments fill up for propose
220.127.116.11 Run the CIP cycle as per the SOP for Operation of CIP.
18.104.22.168 Remove air packets in the cartridge filter assembly by air vent valve during the operation for every 5minutes.
22.214.171.124 Intimate QA to collect the sample of rinse water for its analysis in QC.
126.96.36.199 Collect the CIP sample at the end of cycle by opening the sampling valve and send immediately to rinse water test like:
1. Conductivity 2. pH 3. Absorbance
188.8.131.52 Once the process is completed the CIP IPC will display “Final wash mode Completed successfully”.
184.108.40.206 Now switch off the IPC.
220.127.116.11 If QC result is not OK once again repeat the CIP cycle up to get OK result form QC.
18.104.22.168 Now the Mixing Vessel, Holding vessel Filtration Line and Filter Housing are all ready for SIP operation.
22.214.171.124 Write the Status Board Manufacturing Line is ready for further processing.
126.96.36.199 Verify the CIP cycle print outs. Record the details as per “Equipment Log SOP”.
5.4 CIP OF FILTRATION LINE:
5.4.1 Ensure the CIP in working condition.
5.4.2 Ensure all the utility supply for CIP operation.
5.4.3 Ensure the Holding tank is empty.
5.4.4 Connect the CIP supply to inlet of Holding vessel.
5.4.5 Connect the Holding vessel outlet to the CIP outlet valve.
5.4.6 Clean the outside body of Holding Vessel with Hot WFI using lint free sponge (mopping pad).
5.4.7 Clean the Holding vessel vent filter separately with hot WFI and refit it.
5.4.8 Ensure the purified water and WFI flushing spray ball in working condition.
5.4.9 Close the manhole of the Holding vessel with air tight.
5.4.10 Open the Holding vessel CIP inlet valve and bottom CIP outlet valve.
5.4.11 Now set the IPC of CIP as per following parameter and batch details:
5.4.12 Run the CIP cycle as per SOP for Operation of CIP.
5.4.13 Remove air packets in the air vent valve during the operation.
5.4.14 Intimate QA to collect the sample of rinse water for its analysis in QC.
5.4.15 Collect the CIP sample at the end of cycle by opening the sampling valve and send immediately to rinse water test like
1. Conductivity 2. pH 3. Clarity
5.4.16 Once the process is completed the CIP. IPC will display “Final wash mode Completed successfully”.
5.4.17 Now switch off the CIP.
5.4.18 If QC results are not OK once again repeat the CIP cycle up to get OK result form QC.
5.4.19 Now the Holding vessel is ready for SIP operation.
5.4.20 Write the status board Holding Vessel is ready for processing.
188.8.131.52 Verify the CIP cycle Print Outs. Record the details as per “CIP Log Book”.
5.5 FREQUENCY OF CIP:
After each batch changeover/product changeover.
SOP : Standard Operation Procedure
WFI : Water for Injection
QA : Quality Assurance
CIP : Clean in Place
IPC : Industrials Programmable Control
UV : Ultraviolet
MMV : Mobile mixing vessel
MV : Mixing vessel
BV : Buffer vessel
HV : Holding vessel
Controlled Copy Production
Controlled Copy Quality Assurance
Master Copy Quality Assurance Department
9.0 REVISION HISTORY:
|Revision No.||Change Control No.||Details of Changes||Reason of Changes||Effective Date||Done By|
|00||Not Applicable||Not Applicable||New SOP|